VRC Adaptor from 9Turbo available now @ Quantum!

9TURBO RCUSB-RX2 for RC Simulator Games.
+ Interface RC PPM signal 2 ch to USB-Joystick 2 axis (X,Y)
+ connect via RC receiver, support AM, FM, FM-PCM, FM-HRS , 2.4G all mode.
+ high resolution up to 4000 step for ch1 and ch2.
+ you can use your RC Tramsmitter with Receiver as Windows Joystick-USB for play RC Simulator games.
+ support Virtual RC simulator botn VRC3 and VRC PRO.
+ support OS: Windows XP/2000 /Windows 7 ,NO external driver require.
+ support Game: All windows game that can use USB-JOYSTICK.

Recommend: TRANSMITTER SETTING before do joystick calibration
+ Switch on your transmitter only in "POWER" mode.
+ Transmitter can set to any mode as you want, PPM/PCM/HRS or 2.4G all mode.
+ ST-EPA(ch1) set to maximum, ST-TRIM(ch1) set to 0.
+ TH-EPA(ch2) set to maximum, ST-TRIM(ch2) set to 0.
+ FAIL-SAFE set to INH or OFF.
+ ABS OFF (you can set ABS ON after joystick calibrate finished).
+ D/R and ATL set to 100% (you can adjust to your prefer,after joystick calibrate finished).
+ if your transmitter can set forward side/ reverse side ratio, should set it to FWD50/REV50 (this is not EPA, it is throttle side ratio).

Note:
RCUSB-RX2 must connect with receiver already, before plug it to USB port.
when first plug in 9TURBO RCUSB-RX2 to your computer.
windows will automatic install internal USB driver to this device.
please wait until internal USB driver installation success, then do joystick calibration.

9TURBO RCUSB-DSC-PPM plug servo-3p for Futaba 4PK/4PKS for RC Simulator Games.

+ Interface RC PPM signal 1-4ch to USB-Joystick 2 axis, 2 button.
+ connect via DSC PORT of transmitter.
+ high resolution up to 4000 step for ch1 and ch2.
+ you can use your RC Tramsmitter as Windows Joystick-USB for play RC Simulator games.
+ support Virtual RC simulator botn VRC3 and VRC PRO.
+ support OS: Windows XP/2000 /Windows 7 ,NO external driver require.
+ support Game: All windows game that can use USB-JOYSTICK.

Recommend: TRANSMITTER SETTING before do joystick calibration
+ Switch on your transmitter only in "DISPLAY" mode, don't need to switch on "POWER" mode.
+ Transmitter set to PPM mode.
+ ST-EPA(ch1) set to maximum, ST-TRIM(ch1) set to 0.
+ TH-EPA(ch2) set to maximum, ST-TRIM(ch2) set to 0.
+ ABS OFF (you can set ABS ON after joystick calibrate finished).
+ D/R and ATL set to 100% (you can adjust to your prefer,after joystick calibrate finished).
+ see this page for TIP of setting transmitter for RC-USB connect via DSC port [Click Here].

Note:
when first plug in 9TURBO RCUSB-DSC-PPM to your computer.
windows will automatic install internal USB driver to this device.
please wait until internal USB driver installation success, then do joystick calibration

9TURBO RCUSB-DSC-PPM plug mono 3.5mm for Futaba 3PK/3PKS, Sanwa M8, KO EX10, JR for RC Simulator Games.

+ Interface RC PPM signal 1-4ch to USB-Joystick 2 axis, 2 button.
+ connect via DSC PORT of transmitter.
+ high resolution up to 4000 step for ch1 and ch2.
+ you can use your RC Tramsmitter as Windows Joystick-USB for play RC Simulator games.
+ support Virtual RC simulator botn VRC3 and VRC PRO.
+ support OS: Windows XP/2000 /Windows 7 ,NO external driver require.
+ support Game: All windows game that can use USB-JOYSTICK.

Recommend: TRANSMITTER SETTING before do joystick calibration
+ Switch on your transmitter only in "DISPLAY" mode, don't need to switch on "POWER" mode.
+ Transmitter set to PPM mode.
+ ST-EPA(ch1) set to maximum, ST-TRIM(ch1) set to 0.
+ TH-EPA(ch2) set to maximum, ST-TRIM(ch2) set to 0.
+ ABS OFF (you can set ABS ON after joystick calibrate finished).
+ D/R and ATL set to 100% (you can adjust to your prefer,after joystick calibrate finished).
+ see this page for TIP of setting transmitter for RC-USB connect via DSC port [Click Here].

Note:
when first plug in 9TURBO RCUSB-DSC-PPM to your computer.
windows will automatic install internal USB driver to this device.
please wait until internal USB driver installation success, then do joystick calibration





















9TURBO RCUSB-DSC-PPM plug mini-din4 for Sanwa M11 (M11X can't work) for RC Simulator Games.

+ Interface RC PPM signal 1-4ch to USB-Joystick 2 axis, 2 button.
+ connect via DSC PORT of transmitter.
+ high resolution up to 4000 step for ch1 and ch2.
+ you can use your RC Tramsmitter as Windows Joystick-USB for play RC Simulator games.
+ support Virtual RC simulator botn VRC3 and VRC PRO.
+ support OS: Windows XP/2000 /Windows 7 ,NO external driver require.
+ support Game: All windows game that can use USB-JOYSTICK.

Recommend: TRANSMITTER SETTING before do joystick calibration
+ Switch on your transmitter only in "DISPLAY" mode, don't need to switch on "POWER" mode.
+ Transmitter set to PPM mode.
+ ST-EPA(ch1) set to maximum, ST-TRIM(ch1) set to 0.
+ TH-EPA(ch2) set to maximum, ST-TRIM(ch2) set to 0.
+ ABS OFF (you can set ABS ON after joystick calibrate finished).
+ D/R and ATL set to 100% (you can adjust to your prefer,after joystick calibrate finished).
+ see this page for TIP of setting transmitter for RC-USB connect via DSC port [Click Here].

Note:
when first plug in 9TURBO RCUSB-DSC-PPM to your computer.
windows will automatic install internal USB driver to this device.
please wait until internal USB driver installation success, then do joystick calibration.

For more information, please visit http://www.quantumracing-rc.com/ or contact us at enquiries@quantumracing-rc.com